Leica Digital Camera 2300 User Manual

Update features  
Improvements  
LEICA S (Type 006) -  
Firmware Update 2.3.0.0  
Model, Name Leica S (Type 006)  
Update version 2.3.0.0  
Version FW S 2.3.0.0  
File name S_006_2_3_0_0.FW  
Description of changes  
- Support for the new Leica S lens Leica Elmarit-S 45mm  
f/2.8 ASPH. (CS)  
Update date 2013/10/01  
Access to download  
- New menu language: Korean  
- Improvement to tethered shooting for DNG compressed  
- Flash signal is now output via flash sync socket for any  
exposure time  
Note  
The firmware update for the Leica S (type 006) contains all  
lens firmware updates. After updating your camera, carry out  
an update for your lenses if necessary.  
- Auto bracketing and self-timer settings are saved in the  
user profiles and are active after a restart when previously  
activated  
- The color temperature of the rear panel display has been  
optimized  
- Leica Vario-Elmar-S 30-90 f/3.5-5.6 ASPH.: Focusing  
behavior fault resolved  
- User profiles: Faults resolved  
During the firmware update, you should not:  
- Turn off the camera  
- Remove the battery  
- Detach the lens  
- Remove the memory card  
- The multifunction hand grip may not be attached  
FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT  
IN SERIOUS DAMAGE TO YOUR CAMERA!  
If your camera's functionality is restricted after carrying out  
the firmware update, contact your Leica dealer or your local  
Leica Customer Care center.  
 
Firmware Update 2.3.0.0 / 1  
Step 3:  
Step 4:  
Copy the firmware to a CF or SD memory card  
Install the firmware update  
Preparing the card (formatting):  
1. Remove the card properly from your card reader, insert the  
card into the camera and close the bottom cover.  
2. Press and hold the joystick on the rear of the camera and  
turn on the camera. The update process starts after a few  
seconds. You can now release the joystick. The update  
process is shown as a graphic in the monitor and may take  
several minutes.  
1. Format the memory card in the camera. Information about  
formatting the memory card can be found in the camera  
manual.  
Important:  
When you format the memory card, all the data on it –  
including protected files – will be deleted and cannot be  
recovered without the use of specialist software.  
3. When the installation has been completed successfully,  
turn off the camera. When you turn it on again, the latest  
firmware is active and can be checked in the menu (see  
Step 1).  
2. Insert the formatted memory card into the relevant card  
slot on your PC, or use an external card reader.  
3. Copy the file S_006_2_3_0_0.FW to the master directory  
(*1) on the memory card.  
Note:  
If the battery does not have sufficient charge, a corresponding  
warning message appears in the monitor on the camera.  
(1) Master directory = Top level of memory card - do not copy to one of the  
folders.  
 
Firmware Update 2.3.0.0 / 3  
Step 5:  
Step 6:  
Instructions for installing the  
Check the current firmware version  
Install the lens firmware update  
lens firmware  
Leica recommends updating the lens firmware if you are no  
longer running the latest version.  
1. Remove the memory card from your camera and close the  
cover.  
2. Press and hold the joystick/5-way button/AF/AE lock  
button on the rear of the camera and turn on the camera.  
The update process starts after a few seconds. You can  
now release the joystick. The update process is shown as a  
graphic in the monitor and may take several minutes.  
3. When the installation has been completed successfully, turn  
off the camera. When you turn it on again, the latest lens  
firmware is active and can be checked in the menu (see  
Step 5). You can now use your lens with the latest firmware  
version.  
Important:  
To update the lens firmware, the latest camera firmware  
must be installed on your camera. The relevant lens must  
be attached to perform a lens firmware update.  
1. Attach the relevant lens to the camera.  
2. Turn on the camera.  
3. Open the camera menu with one of the function buttons  
and select the "Firmware" option in the "Setup" category  
using the setting dial or the joystick/5-way button.  
4. Press the setting dial or the joystick/5-way button to  
confirm. The camera and lens firmware versions are  
displayed.  
4. Repeat this procedure for all your S lenses by attaching  
each of the lenses to the camera in turn and updating the  
firmware version.  
5. If the firmware for the attached lens is not the latest  
available version, a corresponding message appears to  
inform you of this. You should carry out a firmware update.  
6. Turn the camera off again.  
Note:  
If the battery does not have sufficient charge, a corresponding  
warning message appears in the monitor on the camera.  
Important:  
The relevant lens must be attached to perform a lens firmware  
update.  
 
4 / Firmware Update 2.3.0.0  

KTM Motorcycle 990 ADVENTURE User Manual
Laser Handheld TV DVBT ST35 User Manual
Lexmark All in One Printer 4039 1XX User Manual
LG Electronics Dishwasher LDF8812BB User Manual
Magellan GPS Receiver Triton 2000 User Manual
Marantz Stereo Amplifier PM4001 User Manual
McCulloch Lawn Mower 4051CM User Manual
Mercury Marine Boat 899183001 User Manual
Metra Electronics Automobile Accessories 99 7581 User Manual
MicroBoards Technology Label Maker PF Pro Disc Printer User Manual